Network config arrays are now split by embedded new lines instead of being evaled into space separated values. This makes it easier to read, maintain and document as discussed on gentoo-dev.

1 files changed, 25 insertions, 20 deletions

diff --git a/conf.d.BSD/net.example b/conf.d.BSD/net.example
index 134bee8..235b605 100644
--- a/conf.d.BSD/net.example
+++ b/conf.d.BSD/net.example
@@ -42,27 +42,29 @@
 # For a static configuration, use something like this
 # (They all do exactly the same thing btw)
 #config_eth0="192.168.0.2/24"
-#config_eth0="'192.168.0.2 netmask 255.255.255.0'"
+#config_eth0="192.168.0.2 netmask 255.255.255.0"
 
 # We can also specify a broadcast
-#config_eth0="'192.168.0.2/24 brd 192.168.0.255'"
-#config_eth0="'192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255'"
+#config_eth0="192.168.0.2/24 brd 192.168.0.255"
+#config_eth0="192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
 
 # If you need more than one address, you can use something like this
 # NOTE: ifconfig creates an aliased device for each extra IPv4 address
 #       (eth0:1, eth0:2, etc)
 #       iproute2 does not do this as there is no need to
-#config_eth0="'192.168.0.2/24' '192.168.0.3/24' '192.168.0.4/24'"
+#config_eth0="192.168.0.2/24
+#192.168.0.3/24
+#192.168.0.4/24'"
 # Or you can use sequence expressions
-#config_eth0="'192.168.0.{2..4}/24'"  FIXME - may not work with baselayout2
+#config_eth0="192.168.0.{2..4}/24"  FIXME - may not work with baselayout2
 # which does the same as above. Be careful though as if you use this and
 # fallbacks, you have to ensure that both end up with the same number of
 # values otherwise your fallback won't work correctly.
 
 # You can also use IPv6 addresses
 # (you should always specify a prefix length with IPv6 here)
-#config_eth0="192.168.0.2/24 \
-#4321:0:1:2:3:4:567:89ab/64 \
+#config_eth0="192.168.0.2/24
+#4321:0:1:2:3:4:567:89ab/64
 #4321:0:1:2:3:4:567:89ac/64"
 
 # If you wish to keep existing addresses + routing and the interface is up,
@@ -70,23 +72,22 @@
 # are no addresses assigned, then we move onto the next step (default dhcp)
 # This is useful when configuring your interface with a kernel command line
 # or similar
-#config_eth0="noop 192.168.0.2/24"
+#config_eth0="noop
+#192.168.0.2/24"
 
 # If you don't want ANY address (only useful when calling for advanced stuff)
 #config_eth0="null"
 
 # Here's how to do routing if you need it
 # We add an IPv4 default route, IPv4 subnet route and an IPv6 unicast route
-#routes_eth0=" \
-#	'default via 192.168.0.1' \
-#	'10.0.0.0/8 via 192.168.0.1' \
-#	'::/0' \
-#"
+#routes_eth0="default via 192.168.0.1
+#10.0.0.0/8 via 192.168.0.1
+#::/0"
 
 # If a specified module fails (like dhcp - see below), you can specify a
 # fallback like so
-#fallback_eth0="'192.168.0.2 netmask 255.255.255.0'"
-#fallback_route_eth0="'default via 192.168.0.1'"
+#fallback_eth0="192.168.0.2 netmask 255.255.255.0"
+#fallback_route_eth0="default via 192.168.0.1"
 
 # NOTE: fallback entry must match the entry location in config_eth0
 # As such you can only have one fallback route.
@@ -211,10 +212,12 @@
 # Surround each ESSID with the " character and seperate them with a space
 # If the first ESSID isn't found then it moves onto the next
 # If this isn't defined then it connects to the first one found
-#preferred_aps="'ESSID 1' 'ESSID 2'"
+#preferred_aps="ESSID 1
+#ESSID 2"
 
 # You can also define a preferred_aps list per interface
-#preferred_aps_eth0="'ESSID 3' 'ESSID 4'"
+#preferred_aps_eth0="ESSID 3
+#ESSID 4"
 
 # You can also say whether we only connect to preferred APs or not
 # Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly"
@@ -234,8 +237,10 @@
 #associate_order_eth0="any"
 
 # You can define blacklisted Access Points in the same way
-#blacklist_aps="'ESSID 1' 'ESSID 2'"
-#blacklist_aps_eth0="'ESSID 3' 'ESSID 4'"
+#blacklist_aps="ESSID 1
+#ESSID 2"
+#blacklist_aps_eth0="ESSID 3
+#ESSID 4"
 
 # If you have more than one wireless card, you can say if you want
 # to allow each card to associate with the same Access Point or not
@@ -354,7 +359,7 @@
 #dns_domain_eth0="your.domain"
 #dns_servers_eth0="192.168.0.2 192.168.0.3"
 #dns_search_eth0="this.domain that.domain"
-#dns_options_eth0="'timeout:1' 'rotate'"
+#dns_options_eth0="timeout:1 rotate"
 #dns_sortlist_eth0="130.155.160.0/255.255.240.0 130.155.0.0"
 # See the man page for resolv.conf for details about the options and sortlist
 # directives