Allow bash arrays to be flattened to make some configs easier.

1 files changed, 35 insertions, 39 deletions

diff --git a/conf.d.BSD/net.example b/conf.d.BSD/net.example
index fe9eec6..9dae103 100644
--- a/conf.d.BSD/net.example
+++ b/conf.d.BSD/net.example
@@ -118,16 +118,16 @@
 # HINTS
 #
 # Most users will just need to set the following options
-# key_ESSID1="s:yourkeyhere enc open" # s: means a text key
-# key_ESSID2="aaaa-bbbb-cccc-dd"      # no s: means a hex key
-# preferred_aps="ESSID 1
-#ESSID 2"
+# key_SSID1="s:yourkeyhere enc open" # s: means a text key
+# key_SSID2="aaaa-bbbb-cccc-dd"      # no s: means a hex key
+# preferred_aps="SSID 1
+#SSID 2"
 #
 # Clear? Good. Now configure your wireless network below
 
 ####################################
 # SETTINGS
-# Hard code an ESSID to an interface - leave this unset if you wish the driver
+# Hard code an SSID to an interface - leave this unset if you wish the driver
 # to scan for available Access Points
 # I would only set this as a last resort really - use the preferred_aps
 # setting at the bottom of this file
@@ -155,70 +155,68 @@
 # Setup any other config commands. This is basically the ifconfig argument
 # without the ifconfig $iface.
 #ifconfig_eth0=""
-# You can do the same per ESSID too.
-#ifconfig_ESSID=""
+# You can do the same per SSID too.
+#ifconfig_SSID=""
 
 # Seconds to wait until associated. The default is to wait 10 seconds.
 # 0 means wait indefinitely. WARNING: this can cause an infinite delay when
 # booting.
 #associate_timeout_eth0="5"
 
-# Define a WEP key per ESSID or MAC address (of the AP, not your card)
+# Define a WEP key per SSID or MAC address (of the AP, not your card)
 # The encryption type (open or restricted) must match the
 # encryption type on the Access Point.
 # To set a hex key, prefix with 0x
-#key_ESSID="0x12341234123412341234123456"
+#key_SSID="0x12341234123412341234123456"
 # or you can use strings. Passphrase IS NOT supported
-#key_ESSID="foobar"
-#key_ESSID="foobar"
+#key_SSID="foobar"
+#key_SSID="foobar"
 
 # WEP key for the AP with MAC address 001122334455
 #mac_key_001122334455="foobar"
 
 # You can also override the interface settings found in /etc/conf.d/net
-# per ESSID - which is very handy if you use different networks a lot
-#config_ESSID="dhcp"
-#routes_ESSID=
-#fallback_ESSID=
+# per SSID - which is very handy if you use different networks a lot
+#config_SSID="dhcp"
+#routes_SSID=
+#fallback_SSID=
 
 # Setting name/domain server causes /etc/resolv.conf to be overwritten
 # Note that if DHCP is used, and you want this to take precedence then
 # please put -R in your dhcpcd options
-#dns_servers_ESSID="192.168.0.1 192.168.0.2"
-#dns_domain_ESSID="some.domain"
-#dns_search_path_ESSID="search.this.domain search.that.domain"
+#dns_servers_SSID="192.168.0.1 192.168.0.2"
+#dns_domain_SSID="some.domain"
+#dns_search_SSID="search.this.domain search.that.domain"
 # Please check the man page for resolv.conf for more information
 # as domain and search (searchdomains) are mutually exclusive and
 # searchdomains takes precedence
 
 # You can also set any of the /etc/conf.d/net variables per MAC address
-# incase you use Access Points with the same ESSID but need different
+# incase you use Access Points with the same SSID but need different
 # networking configs. Below is an example - of course you use the same
 # method with other variables
 #config_001122334455="dhcp"
 #dns_servers_001122334455="192.168.0.1 192.168.0.2"
 
-# Map a MAC address to an ESSID
-# This is used when the Access Point is not broadcasting it's ESSID
-# WARNING: This will override the ESSID being broadcast due to some
-# Access Points sending an ESSID even when they have been configured
+# Map a MAC address to an SSID
+# This is used when the Access Point is not broadcasting it's SSID
+# WARNING: This will override the SSID being broadcast due to some
+# Access Points sending an SSID even when they have been configured
 # not to!
-# Change 001122334455 to the MAC address and ESSID to the ESSID
+# Change 001122334455 to the MAC address and SSID to the SSID
 # it should map to
-#mac_essid_001122334455="ESSID"
+#mac_essid_001122334455="SSID"
 
-# This lists the preferred ESSIDs to connect to in order
-# ESSID's can contain any characters here as they must match the broadcast
-# ESSID exactly.
-# Surround each ESSID with the " character and seperate them with a space
-# If the first ESSID isn't found then it moves onto the next
+# This lists the preferred SSIDs to connect to in order
+# SSID's can contain any characters here as they must match the broadcast
+# SSID exactly.
+# Surround each SSID with the " character and seperate them with a space
+# If the first SSID isn't found then it moves onto the next
 # If this isn't defined then it connects to the first one found
-#preferred_aps="ESSID 1
-#ESSID 2"
+#preferred_aps="SSID1 SSID2"
 
 # You can also define a preferred_aps list per interface
-#preferred_aps_eth0="ESSID 3
-#ESSID 4"
+#preferred_aps_eth0="SSID3 SSID4"
 
 # You can also say whether we only connect to preferred APs or not
 # Values are "any", "preferredonly", "forcepreferred", "forcepreferredonly"
@@ -238,10 +236,8 @@
 #associate_order_eth0="any"
 
 # You can define blacklisted Access Points in the same way
-#blacklist_aps="ESSID 1
-#ESSID 2"
-#blacklist_aps_eth0="ESSID 3
-#ESSID 4"
+#blacklist_aps="SSID1 SSID2"
+#blacklist_aps_eth0="SSID3 SSID4"
 
 # If you have more than one wireless card, you can say if you want
 # to allow each card to associate with the same Access Point or not
@@ -254,7 +250,7 @@
 # essid_eth0 is not set and your card is capable of scanning
 
 # NOTE: preferred_aps  list ignores blacklisted_aps - so if you have
-# the same ESSID in both, well, you're a bit silly :p
+# the same SSID in both, well, you're a bit silly :p
 
 ##################################################
 # wpa_supplicant