diff options
Diffstat (limited to 'doc/net.example.Linux.in')
| -rw-r--r-- | doc/net.example.Linux.in | 88 |
1 files changed, 46 insertions, 42 deletions
diff --git a/doc/net.example.Linux.in b/doc/net.example.Linux.in index 582c161..7955fe3 100644 --- a/doc/net.example.Linux.in +++ b/doc/net.example.Linux.in @@ -864,6 +864,52 @@ #relay_6to4="192.168.3.2" #suffix_6to4=":ff" +#----------------------------------------------------------------------------- +# Advanced Routing +# WARNING: For advanced routing you MUST be using sys-apps/iproute2 +# +# This provides a means to do multi-homing and more using the Routing Policy +# Database (RPDB). +# +# See the following links for background and more information. +# http://linux-ip.net/html/ch-routing.html +# http://linux-ip.net/html/ch-advanced-routing.html + +# The rules listed will be added with 'ip rule add LINE' when the interface is +# being brought up. They will also be removed with 'ip rule delete LINE'. +# The rules added are also stored for later removal, so if you alter your rules +# directly before stopping, you should review your rules again after stopping. + +# Note in earlier versions of openrc, this was provided as an example in +# postup/postdown, however that implementation suffered some bugs in corner +# cases, which are now fixed with this merger. If you used the previous +# example, you should only need to drop the relevent portions of your +# postup/postdown functions, and review the quoting in your rules_IFACE +# variables. + +# Below is a trivial example for a dual-homed connection where there is an OOB +# management network. Only packets explicitly with an address from or to the +# OOB are sent via eth0. All others go via eth1 as the eth1 rules have a lower +# priority. + +# If you want to use names for your tables, you should put lines into +# /etc/iproute2/rt_tables, an example follows: +# 2 oob +# 3 external + +#rules_eth0=" +#from ZZZ.ZZZ.200.128/27 table oob priority 500 +#to ZZZ.ZZZ.200.128/27 table oob priority 550" +#rules_eth1=" +#from XXX.XXX.112.0/24 table external priority 400 +#to XXX.XXX.112.0/24 table external priority 450" +#routes_eth0=" +#ZZZ.ZZZ.200.128/27 dev eth0 table oob scope link +#default via ZZZ.ZZZ.200.129 table oob" +#routes_eth1=" +#XXX.XXX.112.0/24 dev eth1 table external scope link +#default via XXX.XXX.112.1 dev eth1" + #----------------------------------------------------------------------------- # System @@ -992,33 +1038,6 @@ # # This function could be used, for example, to register with a # # dynamic DNS service. Another possibility would be to # # send/receive mail once the interface is brought up. - -# # Here is an example that allows the use of iproute rules -# # which have been configured using the rules_eth0 variable. -# #rules_eth0=" \ -# # 'from 24.80.102.112/32 to 192.168.1.0/24 table localnet priority 100' \ -# # 'from 216.113.223.51/32 to 192.168.1.0/24 table localnet priority 100' \ -# #" -# eval set -- \$rules_${IFVAR} -# if [ $# != 0 ]; then -# einfo "Adding IP policy routing rules" -# eindent -# # Ensure that the kernel supports policy routing -# if ! ip rule list | grep -q "^"; then -# eerror "You need to enable IP Policy Routing (CONFIG_IP_MULTIPLE_TABLES)" -# eerror "in your kernel to use ip rules" -# else -# for x; do -# ebegin "${x}" -# ip rule add ${x} -# eend $? -# done -# fi -# eoutdent -# # Flush the cache -# ip route flush cache dev "${IFACE}" -# fi - #} #postdown() { @@ -1026,21 +1045,6 @@ # # Probably a good idea to set ifdown="no" in /etc/conf.d/net # # as well ;) # [ "${IFACE}" != "lo" ] && ethtool -s "${IFACE}" wol g - -# Automatically erase any ip rules created in the example postup above -# if interface_exists "${IFACE}"; then -# # Remove any rules for this interface -# local rule -# ip rule list | grep " iif ${IFACE}[ ]*" | { -# while read rule; do -# rule="${rule#*:}" -# ip rule del ${rule} -# done -# } -# # Flush the route cache -# ip route flush cache dev "${IFACE}" -# fi - # # Return 0 always # return 0 #} |