From 9a539ebbe1ee0c8557fbcdf22e849534dcbd9b53 Mon Sep 17 00:00:00 2001
From: Mike Frysinger <vapier@gentoo.org>
Date: Wed, 19 Oct 2011 21:30:39 -0400
Subject: further clean up OS differences in makefiles

No need for if() logic.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
---
 conf.d/network.Linux.in | 43 +++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 43 insertions(+)
 create mode 100644 conf.d/network.Linux.in

(limited to 'conf.d/network.Linux.in')

diff --git a/conf.d/network.Linux.in b/conf.d/network.Linux.in
new file mode 100644
index 0000000..f57ec91
--- /dev/null
+++ b/conf.d/network.Linux.in
@@ -0,0 +1,43 @@
+
+# You can assign a default route
+#defaultroute="gw 192.168.0.1"
+#defaultroute6="gw 2001:a:b:c"
+
+# ifconfig under Linux is not that powerful and doesn't easily handle
+# multiple addresses
+# On the other hand, ip (iproute2) is quite powerful and is also supported
+#ip_eth0="192.168.0.10/24; 192.168.10.10/24"
+
+# You can also use ip to add the default route.
+#defaultiproute="via 192.168.0.1"
+#defaultiproute6="via 2001:a:b:c"
+
+# ip doesn't handle MTU like ifconfig, but we can do it like so
+#ifup_eth0="ip link set \$int mtu 1500"
+
+# Create a bonded interface
+#interfaces="bond0"
+#ifup_bond0="modprobe bonding; ifconfig \$int up; ifenslave \$int bge0"
+#ifconfig_bond0="192.168.0.10 netmask 255.255.255.0"
+#ifdown_bond0="rmmod bonding"
+
+# Create tap interface and a bridge interface.
+# We add the tap to the bridge.
+# An external program, like dhcpcd, will configure the IP on the bridge
+#interfaces="tun0 br0"
+#ifup_tun0="tunctl -t \$int"
+#ifdown_tun0="tunctl -d \$int"
+#ifup_br0="brctl addbr \$int; brctl add \$int eth1; brtctl add \$int eth2"
+#ifdown_br0="ifconfig \$int down; btctl delbr \$int"
+
+# Create VLAN
+#interfaces="eth0_2 eth0_3 eth0_4"
+#ifup_eth0="vconfig add \$int 2; vconfig add \$int 3; vconfig add \$int 4"
+#ifconfig_eth0_2="192.168.2.10 netmask 255.255.255.0"
+#ifconfig_eth0_3="192.168.3.10 netmask 255.255.255.0"
+#ifconfig_eth0_4="192.168.4.10 netmask 255.255.255.0"
+#ifdown_eth0="vconfig rem \$int.2; vconfig rem \$int.3; vconfig rem \$int.4"
+
+# Normally you would use wpa_supplicant to configure wireless, but you can
+# use iwconfig also
+#ifup_wlan0="iwconfig \$int key s:secretkey enc open essid foobar"
-- 
cgit v1.2.3