blob: f0c5b770d89d6877b966b215a393368fe6541f19 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
|
# Global OpenRC configuration settings
# Set to "YES" if you want the rc system to try and start services
# in parallel for a slight speed improvement. When running in parallel we
# prefix the service output with it's name as the output will get
# jumbled up.
rc_parallel="NO"
# Set rc_interactive to "YES" and you'll be able to press the I key during
# boot so you can choose to start specific services. Set to "NO" to disable
# this feature.
rc_interactive="YES"
# Do we allow any started service in the runlevel to satisfy the depedency
# or do we want all of them regardless of state? For example, if net.eth0
# and net.eth1 are in the default runlevel then with rc_depend_strict="NO"
# both will be started, but services that depend on 'net' will work if either
# one comes up. With rc_depend_strict="YES" we would require them both to
# come up.
rc_depend_strict="YES"
# Do we allow services to be hotplugged? If not, set to rc_hotplug="NO"
# NOTE: This does not affect anything hotplug/udev/devd related, just the
# starting/stopping of the init.d service triggered by it.
rc_hotplug="YES"
# Dynamic /dev managers can trigger coldplug events which cause services to
# start before we are ready for them. If this happens, we can defer these
# services to start in the boot runlevel. Set rc_coldplug="NO" if you don't
# want this.
# NOTE: This also affects module coldplugging in udev-096 and higher
# If you want module coldplugging but not coldplugging of services then you
# can set rc_coldplug="YES" and rc_plug_services="!*"
rc_coldplug="YES"
# Some people want a finer grain over hotplug/coldplug. rc_plug_services is a
# list of services that are matched in order, either allowing or not. By
# default we allow services through as rc_coldplug/rc_hotplug has to be YES
# anyway.
# Example - rc_plug_services="net.wlan !net.*"
# This allows net.wlan and any service not matching net.* to be plugged.
rc_plug_services=""
# rc_logger launches a logging daemon to log the entire rc process to
# /var/log/rc.log
rc_logger="NO"
# By default we filter the environment for our running scripts. To allow other
# variables through, add them here. Use a * to allow all variables through.
# rc_env_allow="VAR1 VAR2"
##############################################################################
# MISC CONFIGURATION VARIABLES
# There variables are shared between many init scripts
# Set unicode to YES to turn on unicode support for keyboards and screens.
unicode="NO"
# Network fstypes. Below is the default.
net_fs_list="afs cifs coda davfs fuse gfs ncpfs nfs nfs4 ocfs2 shfs smbfs"
##############################################################################
# SERVICE CONFIGURATION VARIABLES
# These variables are documented here, but should be configured in
# /etc/conf.d/foo for service foo and NOT enabled here unless you
# really want them to work on a global basis.
# Some daemons are started and stopped via start-stop-daemon.
# We can set some things on a per service basis, like the nicelevel.
#export SSD_NICELEVEL="-19"
# Pass ulimit parameters
#rc_ulimit="-u 30"
# It's possible to define extra dependencies for services like so
#rc_config="/etc/foo"
#rc_need="openvpn"
#rc_use="net.eth0"
#rc_after="clock"
#rc_before="local"
#rc_provide="!net"
# You can also enable the above commands here for each service. Below is an
# example for service foo.
#rc_foo_config="/etc/foo"
#rc_foo_need="openvpn"
#rc_foo_after="clock"
# You can also remove dependencies.
# This is mainly used for saying which servies do NOT provide net.
#rc_net_tap0_provide="!net"
|
