1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
opt - LLVM optimizer
====================
SYNOPSIS
--------
:program:`opt` [*options*] [*filename*]
DESCRIPTION
-----------
The :program:`opt` command is the modular LLVM optimizer and analyzer. It
takes LLVM source files as input, runs the specified optimizations or analyses
on it, and then outputs the optimized file or the analysis results. The
function of :program:`opt` depends on whether the :option:`-analyze` option is
given.
When :option:`-analyze` is specified, :program:`opt` performs various analyses
of the input source. It will usually print the results on standard output, but
in a few cases, it will print output to standard error or generate a file with
the analysis output, which is usually done when the output is meant for another
program.
While :option:`-analyze` is *not* given, :program:`opt` attempts to produce an
optimized output file. The optimizations available via :program:`opt` depend
upon what libraries were linked into it as well as any additional libraries
that have been loaded with the :option:`-load` option. Use the :option:`-help`
option to determine what optimizations you can use.
If ``filename`` is omitted from the command line or is "``-``", :program:`opt`
reads its input from standard input. Inputs can be in either the LLVM assembly
language format (``.ll``) or the LLVM bitcode format (``.bc``).
If an output filename is not specified with the :option:`-o` option,
:program:`opt` writes its output to the standard output.
OPTIONS
-------
.. option:: -f
Enable binary output on terminals. Normally, :program:`opt` will refuse to
write raw bitcode output if the output stream is a terminal. With this option,
:program:`opt` will write raw bitcode regardless of the output device.
.. option:: -help
Print a summary of command line options.
.. option:: -o <filename>
Specify the output filename.
.. option:: -S
Write output in LLVM intermediate language (instead of bitcode).
.. option:: -{passname}
:program:`opt` provides the ability to run any of LLVM's optimization or
analysis passes in any order. The :option:`-help` option lists all the passes
available. The order in which the options occur on the command line are the
order in which they are executed (within pass constraints).
.. option:: -std-compile-opts
This is short hand for a standard list of *compile time optimization* passes.
It might be useful for other front end compilers as well. To discover the
full set of options available, use the following command:
.. code-block:: sh
llvm-as < /dev/null | opt -std-compile-opts -disable-output -debug-pass=Arguments
.. option:: -disable-inlining
This option is only meaningful when :option:`-std-compile-opts` is given. It
simply removes the inlining pass from the standard list.
.. option:: -disable-opt
This option is only meaningful when :option:`-std-compile-opts` is given. It
disables most, but not all, of the :option:`-std-compile-opts`. The ones that
remain are :option:`-verify`, :option:`-lower-setjmp`, and
:option:`-funcresolve`.
.. option:: -strip-debug
This option causes opt to strip debug information from the module before
applying other optimizations. It is essentially the same as :option:`-strip`
but it ensures that stripping of debug information is done first.
.. option:: -verify-each
This option causes opt to add a verify pass after every pass otherwise
specified on the command line (including :option:`-verify`). This is useful
for cases where it is suspected that a pass is creating an invalid module but
it is not clear which pass is doing it. The combination of
:option:`-std-compile-opts` and :option:`-verify-each` can quickly track down
this kind of problem.
.. option:: -stats
Print statistics.
.. option:: -time-passes
Record the amount of time needed for each pass and print it to standard
error.
.. option:: -debug
If this is a debug build, this option will enable debug printouts from passes
which use the ``DEBUG()`` macro. See the `LLVM Programmer's Manual
<../ProgrammersManual.html>`_, section ``#DEBUG`` for more information.
.. option:: -load=<plugin>
Load the dynamic object ``plugin``. This object should register new
optimization or analysis passes. Once loaded, the object will add new command
line options to enable various optimizations or analyses. To see the new
complete list of optimizations, use the :option:`-help` and :option:`-load`
options together. For example:
.. code-block:: sh
opt -load=plugin.so -help
.. option:: -p
Print module after each transformation.
EXIT STATUS
-----------
If :program:`opt` succeeds, it will exit with 0. Otherwise, if an error
occurs, it will exit with a non-zero value.
|
